av免费观看大全-自拍偷拍你懂的-极品美妇后花庭翘臀娇吟小说-最近中文字幕在线观看视频-国产主播在线看-国产7777777

Automatic dispensing machine is easy to operate, there are two main methods of operation, one is manual, the other is automatic. If manual is used, switch the automatic dispensing machine to manual. If for convenience, you can adjust the switch to the automatic position, as long as you adjust the air pressure and adjustment amount, you can adjust automatically. The dispensing speed is fast, the precision is high, and the needle mouth is not easy to be damaged. Applicable glue: AB glue, silica gel, red glue, UV glue, etc.

一、高速點藥機ts-3000的特點:

The characteristics of TS-3000 are as follows: 1

1. CCD視覺自動定位系統;

1. CCD vision automatic positioning system;

2. 實現更小的點膠直徑，更小單點直徑可達250um;

2. Realize smaller dispensing diameter, and the minimum single point diameter can reach 250um;

3.成熟穩定的高速移動平臺，速度可達1000mm/s，精度0.01mm;

3. mature and stable high-speed mobile platform, with the speed of 1000mm/s and the accuracy of 0.01mm;

4. 用于底部填充、圓片填充、零件涂層保護、粘接、密封等。

4. For bottom filling, disc filling, part coating protection, bonding, sealing, etc.

二世。如何使用高速點膠機:

II. How to use high speed dispenser:

步驟1:將調劑裝置安裝到裝配線上;

Step 1: install the dispensing device on the assembly line;

將料筒插入配藥裝置的推桿中，將機架推入標準裝配線。

Insert the barrel into the push rod of the dispensing device and push the rack into the standard assembly line.

第二步:快速將工件放入點膠機;

The second step: quickly put the workpiece into the dispensing machine;

開始標準生產線,工件沿流程標準生產線,工件將達到快速提取模塊后,傳入的光電檢測開關檢測傳入,傳入的塊氣缸上升,旋轉氣缸將彈出桿,拉缸驅動材料桿將點JiaoGong拉進夾具頂緊模塊,夾塊導桿上升同時,停止生活網上其他構件,夾具檢測夾具自升式襯底得到光電開關,模塊自升式氣缸運動,夾具自升式基材拉桿將被發送到一個工件頂從流水生產線,原噴射完成的同時,旋轉氣缸驅動疏浚桿旋轉90度,和疏浚泥缸返回位置,等待下一個泥。

Start the standard production line, the workpiece will follow the process standard production line, the workpiece will reach the fast extraction module, the incoming photoelectric detection switch detects the incoming, the incoming block cylinder rises, the rotating cylinder will pop up the rod, the pull cylinder drives the material rod to pull the point Jiaogong into the clamp tightening module, the clamp block guide rod rises at the same time, stops other components on the life net, and the clamp detection fixture automatically raises the substrate to get the photoelectric switch, When the module jack up cylinder moves, the clamp jack up base material pull rod will be sent to the top of a workpiece from the flow production line. When the original injection is completed, the rotating cylinder drives the dredging rod to rotate 90 degrees, and the dredging mud cylinder returns to the position, waiting for the next mud.

步驟3:固定工件，準備配藥;

Step 3: fix the workpiece and prepare the dispensing;

工件離開生產線后，進入產品壓縮模塊，產品壓縮模塊開始工作。工件上升后，正方向由側夾缸引導，使工件的長側方向垂直于y軸。保證了兩個橡膠閥與工件的相對位置精度，并將工件固定在產品壓縮裝置中。

After the workpiece leaves the production line, it enters the product compression module, and the product compression module starts to work. After the workpiece rises, the positive direction is guided by the side clamping cylinder, so that the long side direction of the workpiece is perpendicular to the Y axis. The relative position accuracy of the two rubber valves and the workpiece is ensured, and the workpiece is fixed in the product compression device.

步驟4:上膠工件;

Step 4: glue the workpiece;

調劑模塊開始工作，調劑裝置將膠水調劑到工件上。

The adjustment module starts to work, and the adjustment device adjusts the glue to the workpiece.

步驟5:快速將工件送出點膠機;

Step 5: quickly send the workpiece out of the dispensing machine;

產品合模裝置,分配完成后松開工件,工件進入固定產品壓縮模塊模塊,模塊自升式氣缸下降,夾塊氣缸下降,傳入的塊氣缸上升,傳入的光電檢測開關檢測傳入,旋轉氣缸將彈出桿,排出氣缸將一些JiaoGong夾具發出;由點膠部件回原生產線，流向下一站。

The product clamping device releases the workpiece after the distribution is completed. The workpiece enters the fixed top product compression module module. The module jack up cylinder descends, the clamp cylinder descends, the incoming block cylinder rises, the incoming photoelectric detection switch detects the incoming, the rotating cylinder pops up the rod, the exhaust cylinder sends out some Jiaogong clamps; the dispensing part returns to the original production line and flows to the next station.