關于打膠機有幾個常出現的問題要了解
打膠機在上下行程的時候出現混膠不勻，白膠多的問題？
The problem of uneven glue mixing and too much white glue in the up and down strokes of the glue applicator?
這個是壓力桶的內壓過高導致，沒封閉好，解決方法是盡量不要使用帶內壓的膠桶施工，這個工藝太古老了。可以選擇齒輪泵抽壓方式，穩定，出膠量平衡性好，而且不會帶有內壓。帶內壓的都需要施工工人很仔細，否則麻煩多多.
This is caused by the high internal pressure of the pressure bucket, which is not closed well. The solution is to try not to use the rubber bucket with internal pressure for construction. This process is too old. Gear pump pumping mode can be selected, which is stable, with good balance of glue output and no internal pressure. Those with internal pressure need the construction workers to be very careful, otherwise there will be a lot of trouble
打膠機出膠比原來細和少？
Is the glue output of the glue dispenser thinner and less than the original?
打膠機出膠比原來細如果您的膠槍，混膠器都用煤油清理了還這樣的話，需要檢查：看看現在用的膠（看白膠就可以）是不是比以前的膠硬，同樣的壓力，硬的膠比稀的膠出膠量小；打膠機的壓力是不是正常（氣源壓力，油壓），膠管是不是有老化的現象。混膠器堵了，清洗混膠器，和里邊的混膠棒，另外膠嘴也要清洗。
If your glue gun and mixer are cleaned with kerosene, you need to check whether the glue used now (white glue is OK) is harder than the previous glue. Under the same pressure, the amount of hard glue is smaller than that of thin glue; Whether the pressure of the glue applicator is normal (air supply pressure, oil pressure), and whether the rubber hose is aging. If the glue mixer is blocked, clean the mixer and the glue mixing stick inside. In addition, clean the glue nozzle.
打膠機鋁糟探針打膠不準？
Incorrect gluing of aluminum residue probe of gluing machine?
1、放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。
1. Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected.
2、打膠機中間會有一個混膠過程，在供膠機上面混膠完畢之后，需要在電子顯示屏上控制面板上進行選擇“行走設置”。打開界面之后按T1鍵前進行走。在機頭停止時，打開機頭上面B膠閥門，接著在控制面板上找到Esc鍵返回主界面，然后F2狀態設置，在打開界面后按K3鍵供膠開始，當膠嘴中完全混合的膠流出按K4鍵結束供膠。
2. There will be a glue mixing process in the middle of the glue dispenser. After mixing the glue on the glue feeder, you need to select "walking setting" on the control panel on the electronic display screen. Press the T1 key to move forward after opening the interface. When the machine head stops, open the B glue valve on the machine head, then find the ESC key on the control panel to return to the main interface, and then set the F2 status. After opening the interface, press the K3 key to start the glue supply, and when the completely mixed glue in the glue mouth flows out, press the K4 key to end the glue supply.
打膠機故障打第三邊時先吸膠再運行？
Glue dispenser failure when the third side is hit, suck the glue first and then run?
打膠機故障，對平方大的玻璃注膠時，打第三邊時先吸膠再運行，但是出膠量很少是什么原因？以前是直接四邊打完膠再吸膠，現在是打兩邊后吸膠。出現這個問題原因：一，有異物堵塞出膠管道和出膠口。二，氣壓或者液壓壓力減弱。三，膠桶里馬上沒膠了。檢查系統和運行速度。
The glue dispenser fails. When injecting glue into the glass with a large square area, the glue is sucked first and then operated when the third side is applied, but what is the reason for the small glue output? In the past, glue was sprayed directly on four sides and then sucked. Now, glue is sprayed on both sides and then sucked. The reasons for this problem: first, there are foreign objects blocking the glue outlet pipe and the glue outlet. 2、 The air pressure or hydraulic pressure decreases. 3、 There is no glue in the plastic bucket immediately. Check the system and operating speed.
濟南雙組份打膠機長時間停用時，要拔掉電源，這樣不僅可以延長機器的壽命，還可以節省很多傳記費。隨著日益變化的工業發展，液體控制技術和點火器設備也在不斷發展，以超精密控制和多樣化及化。
When Jinan two-component gluing machine is out of service for a long time, unplug the power supply, which can not only prolong the service life of the machine, but also save a lot of biographical fees. With the ever-changing industrial development, liquid control technology and igniter equipment are also developing, with ultra precision control and diversification and specialization.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.cxjrxx.com And consult our staff, will serve you wholeheartedly.
上一篇：雙組份打膠機的結構原理以及打膠操作
下一篇：環氧樹脂灌注膠混膠機相比人工混膠的優勢之處
