點膠機操作流程以及維護保養事項
點膠機主要用于產品工藝中的膠水、油漆以及其他液體精確點、注、涂、點滴到每個產品精確位置，可以用來實現打點、畫線、圓型或弧型。下面來講講點膠機操作流程以及維護保養事項。
Glue dispenser is mainly used to accurately spot, inject, apply and drip glue, paint and other liquids in the product process to the precise position of each product, and can be used to achieve dot, line, circle or arc. Let's talk about the operation process and maintenance of the dispensing machine.
點膠機操作流程：
Operation process of dispensing machine:
一、裝置需要點膠產品的固定架，打開氣壓、機器電源，在膠管內灌入需要運用的膠水，固定好膠管運用高度。
1、 The device requires a fixed frame for dispensing products. Turn on the air pressure and machine power supply, fill the rubber hose with the glue that needs to be used, and fix the application height of the rubber hose.
二、編程：依據產品點膠圖形，編制程序。程序編好后設置點膠速度、Z軸進步高度相對值、點膠時間參數。
2、 Programming: compile the program according to the dispensing graphics of the product. After programming, set the dispensing speed, the relative value of z-axis progressive height, and the dispensing time parameters.
三、參考點設置：進入Setup﹥選擇參考點運用，按下ENTER此參考點將被記載，并在固定架上做上符號。如針頭有變動時則針頭將不在參考點上，通過調整X、Y、Z軸批改參考點，調整完成后按下Home從頭回歸原點，即可設完成。
3、 Reference point setting: enter setup > select reference point application, press enter, this reference point will be recorded, and a symbol will be made on the fixed frame. If the needle changes, the needle will not be on the reference point. Correct the reference point by adjusting the X, y and Z axes. After the adjustment is completed, press home to return to the original point from the beginning, and the setting can be completed.
四、氣壓設定：依據膠水粘稠度設置對應運用氣壓。
4、 Air pressure setting: set the corresponding application air pressure according to the viscosity of the glue.
五、程序、設置完成后，按下機器上的RUN/TEACH開關，放置產品按下Start鍵開始點膠，每換產一只產品，都需按下Start鍵。
5、 After the program and setting are completed, press the run/teach switch on the machine, place the product and press the start key to start dispensing. Press the start key every time you change a product.
點膠機維護保養:
Maintenance of dispensing machine:
1、
濟南雙組份打膠機廠家提醒，更換膠種，需清洗管路。此時先關閉進料閥，打開排料閥，將膠桶剩余膠料排出后，關閉排料閥打開進料閥將清洗溶劑倒入儲膠桶內，機體，按平時操作方式將溶劑壓出沖洗。
1. The manufacturer of Jinan two-component glue applicator reminds that the pipeline needs to be cleaned before changing the glue type. At this time, first close the feeding valve, open the discharging valve, discharge the remaining rubber in the rubber barrel, close the discharging valve, open the feeding valve, pour the cleaning solvent into the rubber barrel, activate the machine body, and press the solvent out for washing according to the normal operation mode.
2、氣壓進氣不正常及發現有水氣，請將調壓過濾器內之水氣排除或檢查氣壓源有無異樣即可。點膠機在膠水大量使用前，請先小量試用，掌握產品的使用技巧，以免差錯,當測試沒問題時，再用雙液滴膠機或雙液灌膠機進行大批量的生產;抽真空系統對膠水進行抽真空除泡處理，以排除攪拌過程中產生的氣泡，或靜置10-20分鐘再使用，以使混合時產生的氣泡及時排除，混合在一起的膠量越多。
2. If the air pressure intake is abnormal and water vapor is found, please remove the water vapor in the pressure regulating filter or check whether the air pressure source is abnormal. Before the glue dispenser is used in large quantities, please try it in small quantities to master the use skills of the product to avoid mistakes. When the test is OK, then use the double liquid glue dropping machine or double liquid glue filling machine for mass production; The vacuum system vacuumizes and defoaming the glue to eliminate the bubbles generated during mixing, or it can be used after standing for 10-20 minutes, so that the bubbles generated during mixing can be eliminated in time, and the more glue mixed together.
3、機臺部分請定期擦拭干凈，以增加使用壽命。混合在一起的膠量越多，其反應就越快，固化速度也會越快，所以要根據實際生產情況進行合理配膠，否則造成膠水的浪費。排除意外，提高生產效率。如今液體控制技術和點膠設備廣泛地應用到現代工業中的各種生產領域。
3. Please wipe the machine regularly to increase its service life. The more glue is mixed together, the faster the reaction will be and the faster the curing speed will be. Therefore, it is necessary to mix the glue reasonably according to the actual production situation, otherwise it will cause a waste of glue. Eliminate accidents and improve production efficiency. Nowadays, liquid control technology and dispensing equipment are widely used in various production fields in modern industry.
In addition, the machine should be unplugged when it is out of service for a long time, which can not only prolong the service life of the machine, but also save a lot of electricity. Come to the website for more relevant content http://www.cxjrxx.com Consult and understand.
上一篇：打膠機在打膠中發生斷膠解決小妙招
下一篇：雙組份打膠機在操作時的注意事項
