打膠機的液壓缸工作不正常原因及維護
雙組份打膠機試用期間會有問題出現，這并不少見，那么你知道打膠機的液壓缸工作不正常原因及維護是怎樣的嗎？下面
濟南雙組份打膠機廠家為您講解。
It is not uncommon for the two-component sealant dispenser to have problems during the trial period. Do you know the cause of abnormal operation of the hydraulic cylinder of the sealant dispenser and how it is maintained? Next, Jinan two-component sealant manufacturer will explain to you.
打膠機的液壓缸工作不正常原因
Reasons for abnormal operation of hydraulic cylinder of glue applicator
A、液壓站工作壓力不正常，檢查比例溢流閥，進行清洗；電機工作是否正常；油泵工作是否正常
A. If the working pressure of the hydraulic station is abnormal, check and clean the proportional overflow valve; Whether the motor works normally; Whether the oil pump works normally
B、電磁換向閥工作是否正常，檢查線圈和閥體
B. Check whether the solenoid directional valve works normally. Check the coil and valve body
C、檢查油管是否有漏油現象
C. Check the oil pipe for oil leakage
D、檢查油缸是否有泄漏現象
D. Check the oil cylinder for leakage
維護與保養：
Maintenance:
A、新機器經過一段時間的運轉之后，應打開護板，檢查各緊固件是否有松動現象，并重新緊固。
A. After a period of operation of the new machine, open the guard board, check whether the fasteners are loose, and retighten them.
B、每次使用完畢，要將機器上的殘膠及灰塵干凈，使傳送帶及機器外表保持清潔。
B. After each use, remove the residual glue and dust on the machine to keep the conveyor belt and machine surface clean.
C、輸送裝置兩側主動輪和從動輪軸承每隔3個月應加注一次潤滑油脂。
C. The driving wheel and driven wheel bearings on both sides of the conveyor shall be filled with lubricating grease every 3 months.
D、液壓系統使用抗磨液壓油應半年更換一次，并定期檢查系統是否有漏油現象。
D. The anti-wear hydraulic oil used in the hydraulic system shall be replaced every six months, and the system shall be checked regularly for oil leakage.
E、環境溫度在5℃以上時，使用46號抗磨液壓油；不高于5℃時，使用32號抗磨液壓油。
E. When the ambient temperature is above 5 ℃, 46 # anti-wear hydraulic oil shall be used; When the temperature is not higher than 5 ℃, use No. 32 anti-wear hydraulic oil.
F、定期檢查電氣接線是否有松動及接地的可靠性。
F. Regularly check whether the electrical wiring is loose and whether the grounding is reliable.
G、B泵的過濾器與過濾器每隔一個月清洗一次。
G. The filter and filter of pump B shall be cleaned every other month.
H、A與B膠的混合器每隔七天清洗一次。
H. The mixer of glue A and glue B shall be cleaned every seven days.
I、連接混合器的連接座每隔一個月清洗一次。
1. The connection seat connecting the mixer shall be cleaned every other month.
J、清洗膠軸套上殘余的膠，保證膠軸套轉動靈活。
J. Clean the residual rubber on the rubber shaft sleeve to ensure that the rubber shaft sleeve can rotate flexibly.
打膠機的液壓缸工作不正常原因及維護相關事項就講解到這里了，您對此有什么不明白的地方就來我們網站
http://www.cxjrxx.com咨詢吧！
The reasons for abnormal operation of the hydraulic cylinder of the glue dispenser and the maintenance related matters are explained here. If you have any questions, please come to our website http://www.cxjrxx.com Consult!
上一篇：打膠機膠頭堵住的情況進行有效處理
下一篇：建議使用雙組份打膠機之前行調試
